Features
Application
Product series
Cable Assembly
PCB connector
2.92mm
2.4mm
Multi Coax PCB Plug Connector
(8 ports)
40GHz
50GHz
(16 ports)
The 1.0 mm connectors are designed for 50 Ohms, excellent performance up to 110 GHz .The 1.0 mm connectors outer conductor ID is 1.0 mm, the interface is air dielectric with the contact supported by a short dielectric bead.
Frontlynk 1.0 mm connector series is for semi-rigid and low-loss flexible cable, adaptor for custom applications.These cable assemblies realize low insertion loss, low reflection loss and well-perform VSWR.
The 1.35 mm Connectors, using for up to 90GHz ( E band).
＊High-performance RF measurements
＊Self-driving vehicles
＊5G applications
The 1.85mm was designed to go beyond the SMA interface constraints, and as a result is NOT SMA compatible. Instead, maximum performance to the highest possible frequency that the geometry would allow, along with repeatable measurements after hundreds or even thousands of interconnects, were the design goals.
The connector outer conductor ID is 1.85 mm, and OD is 4.7 mm, allowing compatibility, so that the 1.85mm connector mates with the 2.4mm connector and has the same ruggedness. It’s a 50 Ohms connector with performance up to 67 GHz.
The 3.5mm series was designed with highly rugged physical interfaces in mind that would mate with SMA dimensions, allowing thousands of repeatable connections. The performance is up to 34 GHz.
The outer contact ID is 3.5 mm, and OD is 4.55 mm. The 3.5mm series is compatible with 2.92mm and SMA series. When mated with SMA and other precision SMA type connectors the performance is limited by the connector with lesser performance.
Frontlynk Surge Arrester series are using for N and 7/16 type.
High Performance from DC to 3 GHz, and 2 to 6 GHz.
Frequencies:
Gas Tube Voltages:90V~350V
Product Specifiction
Cable Type
1.0mm
1.35mm
1.85mm
3.5mm
SMA
N
Impedance (Nominal) Ω
50±1
Maximum Frequency (GHz)
110
90
67
50
40
26.5
18
Overall Diameter (mm)
General Type (HG)
N/A
2.3
3.3
4.1
5.0
Flexible Type (HS)
4.3
7.1
8.2
Universal Type (HF)
3.5
6.2
7.3
VSWR
Typical
1.3
1.2
Spec.
1.4
Amplitude Stability (dB)
±0.07
±0.05
±0.1
Phase Stability (°)
±15
±4
±8
±3
±2
±11.5
±5
Insertion Loss (dB/M)
15
5.7
2.4
1.6
Time Delay (Nominal) (ns/M)
4.28
4.33
Velocity of Propagation (%) (Typical)
78
81
Minimum Bend Radius (mm)
20
12.7
25
Temperature Range (℃) (General Type)
-55 to 125
High Performance Adaptor, from DC to 110GHz. Well-perform VSWR and Insertion loss.
Properties/Series
Working Frequnecy
DC~26.5GHz
DC~40GHz
DC~50GHz
DC~67GHz
VSWR(Typical/Maximum)
1.2/1.3
Phase Stability(°)(Typical/Maximum)
±2/±4
±2/±4.5
±4/±8
Amplitude Stability(dB) (Typical/Maximum)
±0.04/±0.1
±0.02/±0.1
±0.03/±0.1
Minimum bend radius
57.1mm
Temperature
Lab conditions
Lengths(inches)
25", 36", 48" and customized
Ultra Small series.
Specification:
The SMPS connectors are 45% smaller than SMP connectors, SMPS connectors have frequency ranges up to 100GHz. The SMPS connectors were develop to fit smaller and high frequency connectors than SMP and SMPM.
The SMPS RF/Microwave coaxial connectors provide two different levels of retention force: Smooth Bore and Full Detent. Frontlynk SMPS connectors are compatible with all kind of SMPS connectors, including Corning Gilbert's G3PO™ products.
The SMPS RF/Microwave Coaxial connectors are "Push-on" designed, easy to mate connectors, especially for PCB used.
The SMPM connectors are 20% smaller to SMP connectors and have frequency ranges up to 65 GHz. The SMPM connectors were developed to fit for smaller and higher frequency connectors than the SMP.
The SMPM connectors provide two different levels of retention force: Smooth Bore and Full Detent. Bo-Jiang SMPM connectors are compatible with all kinds of SMPM connectors, including Corning Gilbert's GPPO™ products.
The SMPM connectors are "Push-on" designed, easy to mate connectors, especially for PCB used. Applicable for: Aerospace, Broadband, Instrumentation, Routers, Telecom, High-speed Applications, Cable, PC-Board, Surface-Mount Connections.
Frontlynk developed the SMP series to fulfill the customer's demands for higher-frequency and miniaturized connectors. These are easy snap-on connectors; operatible up to 40 GHz.
These SMP connectors are ideal for board to board interconnections by joining plugs on different boards with a jack-to-jack adaptor in between.
The SMP interface provides three different levels of retention force: full detent, limited detent, and smooth bore.Full detent is often used for connections with highest retention, limited detent is only for retaining the bullet, and smooth bore is for the lowest retention.
SMA connectors are subminiature units designed to provide high electrical performance for microwave applications up to 18 GHz.
Constructed with Brass or high quality Stainless Steel, SMA connectors ensure excellent durability and mechanical strength.
SSMA connectors are micro-miniature, high-frequency connectors with threaded mating (smaller version of SMA series), designed to MIL-PRF-39012 requirements.
SSMA connectors provide mechanical reggedness, no matter how small the connector is.
SSMB Serious in a microminiature connectors with snap-on mating (smaller version of SMB series), designed to MIL-PRF-39012 requirements. The design permits rapid connection and disconnection in small spaces, even in inaccessible locations.
SSMB series provides excellent electrical performance in a microminiature footprint. While the snap-on mating interface allows quick installation and dense packaging, the excellent electrical performance of the SSMB series allows it to be used in many applications as an alternative to larger connectors like SMAs.
N connectors are medium size, high quality connectors with a coupling screw system designed for use at frequencies up to 11 GHz.
They are most suitable for use in laboratory tests, satellite TVS, MATVS and other sophisticated electronic applications where high performance and precision are necessary.
TNC connectors are designed with a highly reliable threaded coupling to ensure additional protection against shocks and vibrations.
They are dimensionally and electrically similar to the BNC series, and are especially suitable for use in vibration-exposed equipment such as commercial and military radio telecommunication systems, as well as avionic equipment where a highly durable coupling is needed.
TNC connectors are also widely used in medical equipment, computers and test instrumentation.
BMA Series is an easy use slide-on connector, has 50 Ohms impedance and is suitable for high performance microwave applications up to 18 GHz.
BMA Series preserve mechanical and electrical performance with interfacial misalignment features. The connector used for wireless infrastructure, satellite equipment and test and measurement.
MCX miniature snap-on connectors have 50Ω impedance structure operates in a frequency range up to 6 GHz.
MCX series is ideal for applications of GPS, wireless communication and test instrumentation.
FME connectors were originally developed for the European wireless market, but have recently seen an increase in popularity globally.
Applications are in the GPS, mobile and WLAN sectors of the communications industry.
F series is economically priced connectors specially designed for use with NTSC TV ANTENNA and other similar applications.
Countries using the NTSC System include: The Bahama Islands, Canada, America, Japan, Korea, Mexico, Taiwan, the Philippines, and the U.S.A.
Frontlynk launches the instrumentation grade adaptor between waveguide and coaxial, 1.0mm (W band) to WR-10/WR-15, and 1.85mm to WR-15, per our significant engineering to fulfill higher and higher requirement of the millimeter wave (MMW) coaxial test. These lower Return Loss, and higher stable and durable adaptors also offer the effective conversion between TE10 mode and TEM mode.
Features● Broadband Operation● Remarkable Retune Loss and Insertion Loss● High Stability
Application● Test Setup● Instrumentation● Transceiver● Sub-Assemblies
EIA WR No.
Frequency Band
Frequency Range(GHz)
Coaxial Connector Type
WR-10
W
75～110
WR-12
E
60～90
WR-15
V
50～75、50～67
1.0mm、1.85mm
WR-28
K
26.5～40
DC Blocks are coaxial components that prevent the flow of audio and direct current (DC) frequencies while offering minimum interference to RF signals.
Applications include ground loop elimination, signal source modulation leakage suppression, system signal-to-noise ratio improvement, test setup isolation and other situations where undesired DC or audio current flows in the system.